4PCS Compatible Paper Holder Support Rod Bearing for Graphtec FC8600 FC8000 CE6000 🛠️ High-Quality Compatible Bearing | 4PCS Pack | Paper Holder Support Rod Bearing | Graphtec FC8600 / FC8000 / CE6000 Series

Product Name : Compatible Paper Holder Support Rod Bearing

Packing Quantity : 4 PCS

Condition : Brand New, High Precision, Pre-Lubricated

Core Feature : Perfect Fit | Low-Noise Rotation | Wear-Resistant | Rust-Proof

Applicable Models : Graphtec FC8600, FC8000, CE6000 (All Sizes: 40/60/75/100/120)

ℹ️ PRODUCT NOTE: This is a 4PCS pack of high-quality compatible paper holder support rod bearings designed for Graphtec FC8600, FC8000, and CE6000 cutting plotters. These bearings are critical for the smooth rotation of the paper holder support rod, ensuring stable media feeding and preventing sagging or jamming during cutting. Worn or seized bearings cause noisy operation, uneven media roll rotation, and potential damage to the paper holder assembly. These compatible bearings are manufactured to strict tolerances, pre-lubricated with high-temperature grease, and feature a sealed design to prevent dust and debris ingress. The 4PCS pack provides a complete replacement set for both sides of two support rods, making it ideal for full maintenance. Verify your machine model before purchase to ensure a perfect fit. A cost-effective alternative to OEM parts, these bearings restore smooth media handling and extend the life of your Graphtec plotter’s paper holder system. 4PCS Compatible Paper Holder Support Rod Bearing for Graphtec FC8600, FC8000, CE6000 Cutting Plotters

This 4PCS pack of compatible paper holder support rod bearings is engineered to meet or exceed the performance of the original Graphtec bearings for FC8600, FC8000, and CE6000 series cutting plotters. Designed for the paper holder support rod assembly, these bearings enable smooth, low-friction rotation of the media roll, which is essential for consistent feeding and precise cutting of vinyl, heat transfer film, paper, and other materials.

Crafted from high-quality carbon steel with a sealed, pre-lubricated design, these bearings offer exceptional wear resistance and protection against dust, dirt, and moisture—common causes of premature bearing failure in sign and graphics shops. The precision-machined inner and outer races ensure a perfect fit on the support rod, eliminating play or wobble that can lead to media slippage or uneven cutting. The 4PCS quantity is ideal for replacing all bearings on two support rods (2 bearings per rod), providing a comprehensive maintenance solution for your Graphtec plotter’s paper holder system.

As a direct replacement, these bearings require no modifications or special tools for installation. Simply remove the old, worn bearings and press the new ones into place—your paper holder will operate like new, with quiet, smooth rotation and reliable media support. Whether you’re a sign shop owner, in-house maintenance technician, or hobbyist, this 4PCS bearing pack offers a cost-effective, high-performance solution to keep your Graphtec FC8600, FC8000, or CE6000 plotter running at peak efficiency.

📋 Core Specifications

Product Type : Paper Holder Support Rod Bearing

Quantity : 4 PCS

Material : High-Quality Carbon Steel | Sealed Metal Shield

Lubrication : Pre-Lubricated with High-Temperature, Long-Life Grease

Design : Double-Shielded | Low-Noise | High Rotational Precision

Function : Supports Media Roll | Enables Smooth Rotation | Reduces Friction | Prevents Media Sagging/Jamming

Compatibility : Direct Fit for Graphtec FC8600, FC8000, CE6000 (40/60/75/100/120) Cutting Plotters

Condition : Brand New, Unused, Ready for Installation

🔌 Exact Compatible Graphtec Models

• FC8600 (All Sizes)
• FC8000 (All Sizes)
• CE6000 (All Sizes)

⚠️ COMPATIBILITY WARNING: Only compatible with Graphtec FC8600, FC8000, and CE6000 series plotters! Not suitable for CE5000, CE7000, FC9000, or other Graphtec models. Check your machine’s model number on the rear nameplate before ordering to ensure a proper fit.

🔧 Quick Installation Guide (5–10 Minutes, Basic Tools Required)

⚠️ SAFETY FIRST: POWER OFF | UNPLUG AC CORD | REMOVE MEDIA before starting! Wear gloves to protect hands from sharp edges.

1. Power off the plotter and unplug the power cord. Remove any media roll from the paper holder assembly.
2. Locate the paper holder support rod(s) on the back/side of the plotter. Gently remove the support rod by sliding it out of the mounting brackets (you may need to remove a small retaining clip or screw at one end).
3. Using a pair of pliers or a bearing puller, carefully remove the old bearings from both ends of the support rod. Note the orientation of the bearings (shielded side out) for installation.
4. Clean the support rod with a lint-free cloth to remove any old grease, dust, or debris. Inspect the rod for any signs of wear or damage—replace the rod if necessary.
5. Unpack the 4PCS compatible bearings. Ensure the shielded side is facing outward. Gently press one bearing onto each end of the support rod (use a soft mallet or block of wood to tap the bearing into place—do not hit the bearing directly with a hard hammer).
6. Repeat step 5 for the second support rod (if replacing both). Ensure all bearings are pressed fully onto the rod until they seat against the shoulder or stop.
7. Reinstall the support rod(s) into the mounting brackets. Secure with the retaining clip or screw. Manually rotate the bearings to ensure they spin freely with no noise or binding.
8. Reload your media roll, reconnect the power cord, and power on the plotter. Perform a test cut to verify smooth media feeding and operation.

💡 PRO TIP: For optimal performance, do not over-lubricate the bearings—they are pre-lubricated at the factory. Excess grease can attract dust and debris, leading to premature wear. If the bearings become noisy over time, a small amount of high-temperature bearing grease can be applied to the inner race.

📦 Package Contents

✔ 4 x Compatible Paper Holder Support Rod Bearings (Brand New, Pre-Lubricated)

🏢 Purchase Information

• 4PCS Value Pack : Includes four high-quality compatible bearings—enough to replace all bearings on two paper holder support rods (2 bearings per rod).
• High Precision & Durability : Carbon steel construction with double-shielded design ensures long life, low noise, and smooth rotation in high-volume environments.
• Direct Replacement : Exact fit for Graphtec FC8600, FC8000, CE6000—no modifications needed, quick and easy installation with basic tools.
• Cost-Effective Solution : Meets or exceeds OEM performance at a fraction of the cost, ideal for budget-conscious repair and maintenance.
• Bulk Discounts Available : MOQ=1 Pack (4 PCS). Contact us for volume pricing for repair technicians, sign shops, or plotter service centers.