Geeetech 3D Printer 3D Touch Auto-Leveling Sensor V3.2 Improve Printing in USAuto Bed Leveling SensorHere is the instructions of 3D touch, you can refer to it,click hereAbout this item

• 【Awesome 3D touch Upgraded Kit】Geeetech 3D Touch auto bed leveling kit is a touch-based 3D printer bed leveling probe which enables automatic bed leveling on your 3D printer, then compensates by adjusting the z-axis height during printing.
• 【1-Meter-Long Wire】The 3D Touch Auto Leveling Sensor's standard deviation in repeatability is around 0.04mm that make leveling simple and convenient, equipped with a 1 meter wire to meet various needs of use.
• 【Widely Application】 3D touch sensor works perfectly with most surfaces in the market, PEI / sticker bed / glass bed / metal bed.
• 【Open-source Firmware】Geeetech 3D-Touch Sensor auto leveling sensor for 3D Printers based on open-source, if you want more detail of setting, you can to Search our website.
• 【Notice】This item requires a firmware update, for detailed instructions, please refer to the user manual or watch the viedo instruction . If you need any help, please feel free to contact us.

Please note:3D touch auto leveling sensor is not plug_and_play; you will need to do some modification to your firmware and for some control board, you may need to do some soldering work to the connector. We have prepared the pins for you.
For detailed instructions, please refer to the user manual. If you need any help, please feel free to contact us.Thank you.
Features:1 Simple3DTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor.2 SmartSelf-test: The push pin is operated two times to test when the power is onAlarm: The LED light blinks if a problem found on a self-test or on an operation3 High-precision3DTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise.If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.4. Innovative Solenoid: Ultra Power SavingOn idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.Low power consumption even further drops joule heating, preventing from heat problem.5 Technologies3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin.6 wide Selection of Bed3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor.3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely.7 Optimized structure: Larger Build Size3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor.Specifications:Voltage: 5VCurrent: 15mAMax. Current: 300mACable length: 150mmNet Weight: 10gShipping weight: 25gWiring3-pin: Brown (-, GND), Red (+5V), Orange (control signal)2-pin: Black (-, GND), White (Z min)Package list:1 X 3DTouch Auto leveling sensor 1 X 3Pin Straight Pin1 X 2Pin Straight Pin2 X Screw & Nut & Washer 2 X Dupont Housing Shell 3Pin2 X Dupont Housing Shell 2Pin 3 X Dupont Housing Shell 1Pin 14 X Dupont Terminal1 X 10KΩ 1/8W Resistor Operate condition3DTouch can be operated in the following condition.One I/O for control (PWM or Software PWM)One I/O for Z min (Z Probe)GND and +5V powerCautionAdditional power supply will be needed in case your board does not supply enough amperage.Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)]Pulling/pushing hard on the push-pin can damage 3DTouch and make it less accurate.Fix push-pin with locking paint after reassembling or adjusting core.Do not remove or deform elastic material attached on the push-pin.

Geeetech advocates making 3D printing easy and economical and we are hoping to help more enthusiasts get easy access to the wonderful world of 3D printing.Contact us1. We are always here for you,offering friendly, comprehensive customer service every step of the way. Please follow the good practice to contact us if any doubts and problems.We sincerely hope our item and customer service can give you the BEST BUYING EXPERIENCE on .2. We greatly appreciate your POSITIVE response. Please do NOT leave negative or neutral response without any contact.

On Apr-01-22 at 23:08:33 PDT, seller added the following information:

On May 31, 2022 at 20:58:21 PDT, seller added the following information: