PT1000 Pro High Temperature (400°C) DRHOTSWAP Hotswapable 2MAre you always replacing your thermistor and want reduce down time on your printers? This is fast and cost effective to replace defective thermistor. High Temperature PT1000 Sensor up to 450°C, it possible without amplifier board with default 4.7k pull up resistor but will get lower accuracy. To get full benefits you will need board that supports PT1000 by default like some Bigtreetech boards or replace the 4.7K pullup resister of the thermistor pins with a included 1K 0.1% resister, require SMD soldering. Easily change to different thermistor form factor. [Explore Range] High Accuracy within 1% Extension Cable: 2M Thermistor : PT1000 Thermistor Cartridge: L:15mm , D: 3mm Firmware Changes Required in most Case: For Klipper: Default 4.7K pullup resistor or set thermistor type to PT1000 For Duet2 Wifi M308 S1 P"e0temp" Y"pt1000" R2000 ;two 1K resistors in series for better accuracy Marlin: Default 4.7Kpullup resistor please choose sensor '1047' If you have replaced pullup with 1K resistor please choose sensor '1010' Configuration.h: *1047 : Pt1000 with 4k7 pullup *1010 : Pt1000 with 1k pullup(non standard) #define TEMP_SENSOR_0 1010 #define TEMP_SENSOR_1 0 #define TEMP_SENSOR_2 0 #define TEMP_SENSOR_3 0 #define TEMP_SENSOR_4 0 #define TEMP_SENSOR_BED 1 thermistortable_1010.h: // Pt1000 with 1k0 pullup const short temptable_1010[][2] PROGMEM = { PtLine( 0, 1000, 1000) PtLine( 25, 1000, 1000) PtLine( 50, 1000, 1000) PtLine( 75, 1000, 1000) PtLine(100, 1000, 1000) PtLine(125, 1000, 1000) PtLine(150, 1000, 1000) PtLine(175, 1000, 1000) PtLine(200, 1000, 1000) PtLine(225, 1000, 1000) PtLine(250, 1000, 1000) PtLine(275, 1000, 1000) PtLine(300, 1000, 1000) PtLine(325, 1000, 1000) PtLine(350, 1000, 1000) PtLine(375, 1000, 1000) PtLine(400, 1000, 1000) PtLine(425, 1000, 1000) PtLine(450, 1000, 1000) }; thermistortable_1047.h: // Pt1000 with 4k7 pullup const short temptable_1047[][2] PROGMEM = { // only a few values are needed as the curve is very flat PtLine( 0, 1000, 4700) PtLine( 50, 1000, 4700) PtLine(100, 1000, 4700) PtLine(150, 1000, 4700) PtLine(200, 1000, 4700) PtLine(250, 1000, 4700) PtLine(300, 1000, 4700) PtLine(350, 1000, 4700) PtLine(400, 1000, 4700) PtLine(450, 1000, 4700) }; PT1000 Pro High Temperature (400°C) DRHOTSWAP Hotswapable 2M
All Prices include GST. Message us if require a tax invoice.
Are you always replacing your thermistor and want reduce down time on your printers? This is fast and cost effective to replace defective thermistor.
- High Temperature PT1000 Sensor up to 450°C, it possible without amplifier board with default 4.7k pull up resistor but will get lower accuracy. To get full benefits you will need board that supports PT1000 by default like some Bigtreetech boards or replace the 4.7K pullup resister of the thermistor pins with a included 1K 0.1% resister, require SMD soldering.
- Easily change to different thermistor form factor. [Explore Range]
- High Accuracy within 1%
Extension Cable: 2M
Thermistor : PT1000
Thermistor Cartridge: L:15mm , D: 3mm
Firmware Changes Required in most Case:
For Klipper:
Default 4.7K pullup resistor or set thermistor type to PT1000
For Duet2 Wifi
M308 S1 P"e0temp" Y"pt1000" R2000 ;two 1K resistors in series for better 4.7Kpullup resistor please choose sensor '1047'If you have replaced pullup with 1K resistor please choose sensor '1010'
Configuration.h:*1047 : Pt1000 with 4k7 pullup*1010 : Pt1000 with 1k pullup(non standard)#define TEMP_SENSOR_0 1010#define TEMP_SENSOR_1 0#define TEMP_SENSOR_2 0#define TEMP_SENSOR_3 0#define TEMP_SENSOR_4 0#define TEMP_SENSOR_BED 1thermistortable_1010.h:// Pt1000 with 1k0 pullupconst short temptable_1010[][2] PROGMEM = ;thermistortable_1047.h:// Pt1000 with 4k7 pullupconst short temptable_1047[][2] PROGMEM = ; HAVE A QUESTION OR CONCERN?
If you need more information regarding this item, please message us or check on original manfuacturers websites.
DREMC STORE back our products and pride ourselves, not only in quality but in genuine products. Please do not hesitate to reach out to us. We stock the largest range of 3D Printer Spares Parts, from Manufacturer such as E3D-Online, Creality, Slice Engineering, Bondtech, Micro Swiss, LDO Motors, Bigtreetech, Trianglelabs to name a few.
We are the largest Australia Creality Spare Part Distributors based in Brisbane, we stock over 200 SKUs Creality Printers spares parts. Our website store.dremc.com.au for latest stock list and accurate real time stock counter, no hidden stock levels.
Do you need bulk spare parts or DREMC / Polymaker filament discount? Message us now if you require B2B/Educational payment terms.
Please check out our response to see what others are saying about us.
× × × × ×
Tell a friend Visit store Watch now Postage info
Click the Postage tab above the listing description for more info
Click the Postage tab above the listing description for more info!
Additional delivery notes
PICK UP OPTION
Sorry, our items are NOT available for pick-up.
PAYING VIA PAYPAL/CARD
Please refer to Checkout for available payment method.
Price include GST. Message us if require a tax invoice.
Additional Information
No additional information at this time
Ask seller a question
You might also like BIGTREETECH SKR MINI E3 V3.0 32 Bit Control Board for Ender 3 Series Ender 5 Official Creality CR-6 Series (CR-6 SE, CR-6 Max, CR-10 Smart) Control Mainboard Titanium Alloy Bi-Metal Heatbreaker For ANYCUBIC Mega S / Mega Pro / Vyper Trianglelab CR6 SE Titanium alloy Bi-Metal Heat break For CR-6 SE Ender 3 Neo Contact
To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.
Ask seller a question
© DREMC STORE
Postage
Click the Postage tab above the listing description for more info
Returns
Returns are accepted
Items must be returned within 30 days of the sale ending
Buyer will pay for return shipping.
integration by